View A080SN01-V4_3710831.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

customer approval sheet company name model a080sn01 v4 customer approved title : name : approval for specifications only (spec. ver. ) approval for specifications and es sample (spec. ver. ) approval for specifications and cs sample (spec. ver. ) customer remark : auo pm : p/n : comment : doc. version : 0.4 total pages : 32 www.datasheet.co.kr datasheet pdf - http://www..net/
all rights strictly reserved. any portion of this pa per shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. date : 2009/02/19 product specification 8.0" color tft-lcd panel model name: a080sn01 v4 (91.08a07.400) < >preliminary specification < >final specification note: the content of this specification is subject to change. ? 2009 au optronics all rights reserved, do not copy. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 1/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. record of revision version revise date page content 0.0 2008/08/18 all first draft. 0.1 2008/11/06 4 update fpc connnector 6 update recommended connector 24 update viewing angle 0.2 2008/11/12 24 update response time 0.3 2009/01/07 17 update serial register ta ble 18 delete r1 setting 0.4 2009/02/19 10 update electrical characteristics www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 2/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. contents a. general information................................ ................................................... .................................................. 3 b. outline dimension .................................. ................................................... .................................................. 4 1. tft-lcd module C front view..................... ................................................... ............................................ 4 2. tft-lcd module C rear view ...................... ................................................... ........................................... 5 c. electrical specifications .......................... ................................................... ................................................ 6 1. tft lcd panel pin assignment .................... ................................................... .......................................... 6 2. backlight driving section.......................... ................................................... ................................................. 9 3. absolute maximum ratings........................ ................................................... .............................................. 9 4. electrical dc characteristics...................... ................................................... .............................................. 9 5. electrical ac characteristics ...................... ................................................... .............................................11 6. rgb parallel input timing ....................... ................................................... ................................................11 7. serial interface characteristics .................. ................................................... ............................................ 14 8. power on/off characteristics..................... ................................................... ............................................ 20 d. optical specification .............................. ................................................... ................................................ 23 e. reliability test items ............................. ................................................... ................................................. 25 f. packing and marking ................................ ................................................... .............................................. 26 1. packing form ...................................... ................................................... ................................................... 26 2. module/panel label information .................. ................................................... .......................................... 27 3. carton label information........................ ................................................... ................................................ 27 g. application note ................................... ................................................... .................................................. 2 8 1. application circuit .............................. ................................................... ................................................... .. 28 2. system block ..................................... ................................................... ................................................... .. 31 h. precautions ........................................ ................................................... ................................................... .. 32 www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 3/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. a. general information this product is for portable dvd and digital photo f rame application. no. item unit specification remark 1 screen size inch 8.0(diagonal) 2 display resolution dot 800rgb(h)600(v) 3 overall dimension mm 170.1(w) 132.3(h) 1.44(d ) note 1 4 active area mm 162.0(w)x121.5(h) 5 pixel pitch mm 0.2025(w)x0.2025(h) 6 color configuration -- r. g. b. stripe note 2 7 color depth -- 16.7m colors note 3 8 ntsc ratio % 50 9 display mode -- normally white 10 panel surface treatment -- anti-glare, 3h 11 weight g 65 12 panel power consumption w 2.3 note 4 13 backlight power consumption w xx 14 viewing direction 6 oclock (gray inversion) note 1: not include blacklight cable and fpc. refer next page to get further information. note 2: below figure shows dot stripe arrangement. note 3: the full color display depends on 24-bit dat a signal (pin 4~27). note 4: please refer to electrical characteristics chapter. . . ( 1 2 3 .2398 2399 2400) (1 ..600) www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 4/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transforme d to any other forms without permission from au optronics corp. b. outline dimension 1. tft-lcd module C front view www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 5/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transforme d to any other forms without permission from au optronics corp. 2. tft-lcd module C rear view www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 6/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. c. electrical specifications 1. tft lcd panel pin assignment recommended connector : xf2m-6015-1ah pin no symbol i/o description remark 1 agnd p analog ground 2 avddio p analog power 3 vddio p digital power 4 dr0 i red data input (lsb) 5 dr1 i red data input 6 dr2 i red data input 7 dr3 i red data input 8 dr4 i red data input 9 dr5 i red data input 10 dr6 i red data input 11 dr7 i red data input (msb) 12 dg0 i green data input (lsb) 13 dg1 i green data input 14 dg2 i green data input 15 dg3 i green data input 16 dg4 i green data input 17 dg5 i green data input 18 dg6 i green data input 19 dg7 i green data input (msb) 20 db0 i blue data input (lsb) 21 db1 i blue data input 22 db2 i blue data input 23 db3 i blue data input 24 db4 i blue data input 25 db5 i blue data input 26 db6 i blue data input 27 db7 i blue data input (msb) 28 dclk i data clock input 29 de i data enable input 30 hsync i horizontal sync input. negative polarity 31 vsync i vertical sync input. negative polarity 32 scl i serial communication clock input 33 sda i/o serial communication data input www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 7/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. 34 csb i serial communication chip select 35 fba - for test, do not connect (please leave it op en) 36 vddio p digital power 37 drva - for test, do not connect (please leave it o pen) 38 gnd p digital ground 39 agnd p analog ground 40 avddio p analog power 41 vcomin i for external vcom dc input (optional) 42 dith i dithering setting dith = "l" 6bit resolution(last 2 bits of input data turncated) dith = "h" 8bit resolution(default setting) 43 nc - not connect 44 vcom o connect a capacitor 45 v(10) p gamma correction voltage reference 46 v(9) p gamma correction voltage reference 47 v(8) p gamma correction voltage reference 48 v(7) p gamma correction voltage reference 49 v(6) p gamma correction voltage reference 50 v(5) p gamma correction voltage reference 51 v(4) p gamma correction voltage reference 52 v(3) p gamma correction voltage reference 53 v(2) p gamma correction voltage reference 54 v(1) p gamma correction voltage reference 55 nc - not connect 56 vgh p positive power for tft 57 vddio p digital power 58 vgl p negative power for tft 59 gnd p digital ground 60 cap c connected to a capacitor i: input pin; p: power pin; g: ground pin; c: capacit or pin www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 8/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. note 1: frp is the output of vcom driver. it is the same phase and amplitude with common electrode driving signal (vcom). the vcom amplitude and dc le vel setting can be adjusted through serial control. note 2: the polarity of vcom should be generated fr om pol through driving circuit. the h/l voltage leve l of pol is vddio/gnd. hence, it cannot be used as vco m signal directly. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 9/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. 2. backlight driving section no. symbol i/o description remark 1 vled i led power supply -- 2 gndled - led ground -- 3. absolute maximum ratings item symbol condition min. max. unit remark vddio gnd=0 -0.5 5 v avddio agnd=0 -0.5 15 v v gh -0.3 42 v v gl gnd=0 -20 0.3 v power voltage v gh v gl - 40 v v i -0.3 vddio+0.3 v note 1 input signal voltage vcom 0 6.5 v operating temperature topa -10 60 storage temperature tstg -20 70 note 1: hs , vs , de , digital data note 2: functional operation should be restricted und er ambient temperature (25 ). note 3: maximum ratings are those values beyond which damag es to the device may occur. functional operation should be restricted to the limits in the electrical characteristics chapter. 4. electrical dc characteristics a. typical operation condition (agnd =gnd = 0v) item symbol min. typ. max. unit remark vddio 2.7 3.3 3.6 v i vddio - 11 14 ma black pattern@vddio=3.3 avddio 11 11.68 12 v i avddio - 16 20 ma black pattern power supply v gh 7 15 vee+40 v www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 10/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. i vgh - 0.16 0.2 ma black pattern v gl -20 -6.75 -5 v i vgl - 0.16 0.2 ma black pattern power consumption p - 230 260 mw black pattern vcom v cdc 3.9 4.1 4.3 v dc component h level v ih 0. 7 vddio - vddio v input signal voltage l level v il 0 - 0.3 vddio v note 1 input level of v1~v5 vx 0.4*avdd - avdd-0.5 positive gamma correction voltage note 2 input level of v6~v10 vx 0.5 - 0.6*avdd negative gamma correction voltage note 2 note 1: hs , vs , de, digital data note 2 : agnd version: 0.4 page: 11/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. 5. electrical ac characteristics a. signal ac characteristics parameter symbol min. typ. max. unit. remark clock high time t wcl 8 - - ns clock low time t wch 8 - - ns hsync setup time t hsu 5 - - ns hsync hold time t hhd 10 - - ns vsync setup time t vsu 0 - - ns vsync hold time t vhd 2 - - ns data setup time t dsu 5 - - ns data hold time t dhd 10 - - ns data enable set-up time t esu 4 - - ns data enable hold time t ehd 2 - - ns 6. rgb parallel input timing a. horizontal timing parameter symbol min. typ. max. unit. remark dclk frequency f dclk 25 40 45 mhz dclk period t dclk 22 25 40 ns hsync period (= t hd + t hbl ) t h 986 1056 1183 dclk active area t hd - 800 - dclk www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 12/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. horizontal blanking (= t hf + t he ) t hbl 186 256 383 dclk hsync front porch t hf - 40 - dclk delay from hsync to 1 st data input (= t hw + t hb ) t he 88 216 343 dclk function of hdl[7..0] settings hsync pulse width t hw 1 128 136 dclk hsync back porch t hb 10 88 342 dclk horizontal input timing (hv mode) horizontal input timing (de mode) b. vertical timing parameter symbol min. typ. max. unit. remark www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 13/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. vsync period (= t vd + t vbl ) t v 620 628 635 th active lines t vd - 600 - vertical blanking (= t vf + t ve ) t vbl 20 28 35 th vsync front porch t vf - 1 - th gd start pulse delay t ve 19 27 34 hs function of vdl[3..0] settings vsync pulse width t vw 1 3 16 th hsync/vsync phase shift t vpd 2 320 - dclk vertical timing (hv mode) vertical timing (de mode) www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 14/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. 7. serial interface characteristics a. serial control interface ac characteristic 1. each serial command consists of 16 bits of data whi ch is loaded one bit a time at the rising edge of serial clock scl. 2. command loading operation starts from the fallin g edge of cs and is completed at the next rising edg e of cs. 3. the serial control block is operational after power on reset, but commands are established by the vsync signal. if command is transferred multiple time s for the same register, the last command before the vsync signal is valid. command1 for r0 command2 for r0 command3 for r1 command4 for r2 command5 for r5 command6 for r7 vsync cs established commands: command 2 command 3 command 4 4. if less than 16 bits of scl are input while cs is low, writing command cannot be established. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 15/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. 5. if 16 bits or more of scl are input while cs is l ow, the first 16 bits of transferred data before th e rising edge of cs pulse are valid data. 6. serial block operates with the scl clock. 7. serial data can be accepted in the standby (power s ave) mode. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 16/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. b serial interface timing msb lsb a6 a5 a4 a3 r/w a2 a1 a0 d7 d6 d5 d4 d3 d2 d1 d0 address r/w address data write mode: read mode: www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 17/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. c. register table (default value) when grb is low, all registers reset to default val ues, which are in the brackets. serial commands are executed at next vsync signal. reg address r/w data no. d15 d14 d13 d12 d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d0 r0 0 0 0 0 0 (01) (01) (1) u/d (0) shl (1) (0) (0) grb (1) stb (1) r1 0 0 0 1 0 (0) (1) (01) (2fh) r2 0 0 1 0 0 hdl (80h) r3 0 0 1 1 0 (0) (0) (0) (0) (0) vdl (1000) r4 0 1 0 0 0 (1) (0) (0) (0) (1) (1111) r6 0 1 1 0 0 (0) engb12 (1) engb11 (1) engb10 (1) (0) (0) engb5 (1) engb4 (1) engb3 (1) (0) x => reserved bit, please set to 0. sending serial commands periodically is recommended t o improve esd protection ability. d. register description when grb is low, all registers reset to default val ues, which are in the brackets. serial commands are executed at next vsync signal. 1.. r0 setting address bit description default 0000 [10..0] bits 10-9 auo internal use 01 bits7-8 auo internal use 01 bit6 (dith) dithering function. 1 bit5 (u/d) vertical shift direction selection. 0 bit4 (shl) horizontal shift direction selection. 1 bit3 (shdb1) avdd dc-dc converter shutdown setting. 1 bit2 auo internal use 0 bit1 (grb) global reset. 1 bit0 (stb) standby mode setting. 1 bit6 dith function 0 dith off. 1 dith on. (default) www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 18/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. bit5 u/d function 0 scan down; first line= gn -> gn-1 -> -> g2 -> l ast line=g0. (default) 1 scan up; first line= g0 -> g2 -> -> gn-1 -> last line=gn bit4 shl function 0 shift left; first data= y600 -> y599 -> -> y2 -> last data=y1. 1 shift right; first data= y1 -> y2 -> -> y599 -> last data=y600. (default) bit3 shdb1 function 0 avdd dc-dc converter is off. 1 avdd dc-dc converter is on. (default) bit1 grb function 0 the controller is reset. reset all registers to d efault value. 1 normal operation. (default) bit0 stb function 0 t-con, source driver and dc-dcs converters are of f. all outputs are set to gnd. 1 normal operation. (default) 2. r2 setting address bit description default 0010 [7..0] bit7-0(hdl) horizontal start pulse adjus tment function 80h bit7-0 hdl function 00h t he = t hetyp - 128 clk period. 80h t he = t hetyp . (default) ffh t he = t hetyp + 127 clk period. 3. r3 setting address bit description default 0011 [8..0] bit8 auo internal use 0 bit7 auo internal use 0 bit6 auo internal use 0 bit5 auo internal use 0 bit4 auo internal use 0 bit3-0(vdl) vertical start pulse adjustment function 1000 www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 19/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. bit3-0 vdl function 0000 t ve = t vetyp C 8 hs period. 0001 t ve = t vetyp C 7 hs period. 0010 t ve = t vetyp C 6 hs period. 0011 t ve = t vetyp C 5 hs period. 0100 t ve = t vetyp C 4 hs period. 0101 t ve = t vetyp C 3 hs period. 0110 t ve = t vetyp C 2 hs period. 0111 t ve = t vetyp C 1 hs period. 1000 t ve = t vetyp. (default) 1001 t ve = t vetyp C 1 hs period. 1010 t ve = t vetyp C 2 hs period. 1011 t ve = t vetyp C 3 hs period. 1100 t ve = t vetyp C 4 hs period. 1101 t ve = t vetyp C 5 hs period. 1110 t ve = t vetyp C 6 hs period. 1111 t ve = t vetyp C 7 hs period. 4. r6 setting address bit description default 0110 [9..0] bits9 auo internal use 0 bits8(engb12) gamma buffer enable for v9 1 bits7(engb11) gamma buffer enable for v8 1 bits6(engb10) gamma buffer enable for v7 1 bits5 auo internal use 0 bits4 auo internal use 0 bits3(engb5) gamma buffer enable for v4 1 bits2(engb4) gamma buffer enable for v3 1 bits1(engb3) gamma buffer enable for v2 1 bits0 auo internal use 0 bitx engbx function 0 gamma buffer for vx is disabled (high z). 1 gamma buffer is enabled. vx must be connected exter nally. x => reserved bit, please set to 0. sending serial commands periodically is recommended t o improve esd protection ability. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 20/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. 8. power on/off characteristics a. recommended power on register setting address r/w data reg no . d15 d14 d13 d12 d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d0 r0 0 0 0 0 0 10 01 1 0 1 0 0 1 1 r1 0 0 0 1 0 0 01 01 2fh r2 0 0 1 0 0 0 0 0 80h r3 0 0 1 1 0 0 0 0 0 0 0 0 1000 r4 0 1 0 0 0 0 0 1 1 00 1 1111 r6 0 1 1 0 0 0 0 1 1 1 0 0 1 1 1 0 note : start to provide spi commend at least after 2 frame. 1. send r15 : 000h(normal register bank) at first. 2. wait at least after more than one frame, send r0 : 4d1h(global reset) 3. after send global reset, start to send r0 to r6 recommend register value. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 21/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transforme d to any other forms w ithout permission from au optronics corp. b. recommended power on sequence www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 22/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transforme d to any other forms w ithout permission from au optronics corp. c. power off sequence www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 23/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. d. optical specification all optical specification is measured under typical co ndition (note 1, 2) item symbol condition min. typ. max. unit remark response time rise fall tr tf =0 -- -- 4 16 8 32 ms ms note 3 contrast ratio cr at optimized viewing angle 300 400 -- note 4 top bottom left viewing angle right c r 1 0 40 55 60 60 50 65 70 70 -- -- -- -- deg. note 5 transmission y l =0 4.0 4.5 -- % note 1: ambient temperature =25 , and led lightbar voltage v l = 12 v. to be measured in the dark room. note 2: to be measured on the center area of panel w ith a viewing cone of 1 by topcon luminance meter bm-5a, after 15 minutes operation. center of the screen field=1 note 3: definition of response time: the output signals of photo detector are measured w hen the input signals are changed from black to white(falling time) and from white to black(rising time), respectively. the response time is defined as the time interval between the 10% and 90% of amplitudes. refer to figure as below. bm-5a www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 24/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. s i g n a l ( r e l a t i v e v a l u e ) "black" tr tf "white" "white" 0% 10% 90% 100% note 4.definition of contrast ratio: contrast ratio is calculated with the following for mula. status black" " at is lcd when output detector photo status white" " at is lcd when output detector photo (cr) ratio contrast = note 5. definition of viewing angle, , refer to figure as below. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 25/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. e. reliability test items no. test items conditions remark 1 high temperature storage t a = 7 0 240hrs 2 low temperature storage ta= -20 240hrs 3 high ttemperature operation tp = 6 0 240hrs 4 low temperature operation ta= -10 240hrs 5 high temperature & high humidity tp= 5 0 . 80% rh 240hrs operation 6 heat shock - 1 0 ~ 6 0 , 50 cycle, 1hrs/cycle non-operation 7 vibration (with carton) random vibration: 0.015g 2 /hz from 5~200hz C6db/octave from 200~500hz iec 68-34 8 drop (with carton) height: 60cm 1 corner, 3 edges, 6 surfaces note 1: ta: ambient temperature. tp: panel surface temperature note 2: in the standard conditions, there is not dis play function ng issue occurred. all the cosmetic specification is judged before the reliability stres s. note 3: all the cosmetic specification is judged befor e the reliability stress. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 26/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. f. packing and marking 1. packing form 84.08a07.002 www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 27/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. 2. module/panel label information the module/panel (collectively called as the product ) will be attached with a label of shipping number which represents the identification of the product at a specific location. refer to the product outline dra wing for detailed location and size of the label. the label i s composed of a 22-digit serial number and printed w ith code 39/128 with the following definition: example: 501m06zl06123456781z05: product manufacturing week code: wk50 product version: version 1 product manufactuing factory: m06 3. carton label information the packing carton will be attached with a carton lab el where packing qty, auo model name, auo part number, customer part number (optional) and a serie s of carton number in 13 or 14 digits are printed. the carton number is apparing in the following format: refer to the drawing of packing format for the locat ion and size of the carton label. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 28/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. g. application note 1. application circuit www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 29/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. avdd v1 v2 v3 v4 v5 v6 v7 v9 v10 v8 r301 2k/1%/0603 r302 0/5%/0603 r303 6.8k/1%/0603 r304 0/5%/0603 c 3 0 4 1 u f / 1 6 v / x 5 r / 0 6 0 3 c 3 0 3 1 u f / 1 6 v / x 5 r / 0 6 0 3 c 3 0 5 1 u f / 1 6 v / x 5 r / 0 6 0 3 c 3 0 6 1 u f / 1 6 v / x 5 r / 0 6 0 3 c 3 0 7 1 u f / 1 6 v / x 5 r / 0 6 0 3 c 3 0 8 1 u f / 1 6 v / x 5 r / 0 6 0 3 c 3 0 2 0 . 1 u f / 1 6 v / x 5 r / 0 4 0 2 c 3 0 9 1 u f / 1 6 v / x 5 r / 0 6 0 3 c 3 0 1 1 0 u f / 1 6 v / x 5 r / 1 2 0 6 c 3 1 0 1 u f / 1 6 v / x 5 r / 0 6 0 3 r306 0/5%/0603 r305 1.43kk/1%/0603 r308 0/5%/0603 r307 1k/1%/0603 c 3 1 1 1 u f / 1 6 v / x 5 r / 0 6 0 3 r310 0/5%/0603 r309 2.2k/1%/0603 r312 0/5%/0603 c 3 2 2 1 u f / 1 6 v / x 5 r / 0 6 0 3 r311 6.8k/1%/0603 r322 0/5%/0603 r321 1.54k/5%/0603 r320 0/5%/0603 r319 3.74k/1%/0603 r318 0/5%/0603 r317 1.5k/1%/0603 r316 0/5%/0603 r315 1.1k/1%/0603 r314 0/5%/0603 r313 2k/1%/0603 10.84 8.21 7.65 7.26 6.42 3.81 3.04 2.61 2.04 0.60 www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 30/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. vcomin avdd avdd r325 0/5%/0603 + - u301a no(ad8565) 3 4 2 5 1 vr301 30kvr c324 1 0u f / 1 0v / x 5 r / k / 0 805 c323 0. 1uf / 16 v / x 5r / k / 04 02 r323 40k/5%/0603 r324 30k/5%/0603 www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 31/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. 2. system block www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 32/32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms w ithout permission from au optronics corp. h. precautions 1. do not twist or bend the module and prevent the unsuitable external force for display module during assembly. 2. adopt measures for good heat radiation. be sure to use the module with in the specified temperature . 3. avoid dust or oil mist during assembly. 4. follow the correct power sequence while operating . do not apply the invalid signal, otherwise, it wi ll cause improper shut down and damage the module. 5. less emi: it will be more safety and less noise. 6. please operate module in suitable temperature. t he response time & brightness will drift by differe nt temperature. 7. avoid to display the fixed pattern (exclude the white pattern) in a long period, otherwise, it will cause image sticking. 8. be sure to turn off the power when connecting or d isconnecting the circuit. 9. polarizer scratches easily, please handle it caref ully. 10. display surface never likes dirt or stains. 11. a dewdrop may lead to destruction. please wipe o ff any moisture before using module. 12. sudden temperature changes cause condensation, an d it will cause polarizer damaged. 13. high temperature and humidity may degrade perfo rmance. please do not expose the module to the direct sunlight and so on. 14. acetic acid or chlorine compounds are not friends with tft display module. 15. static electricity will damage the module, please do not touch the module without any grounded device. 16. do not disassemble and reassemble the module by self. 17. be careful do not touch the rear side directly. 18. no strong vibration or shock. it will cause module broken. 19. storage the modules in suitable environment wit h regular packing. 20. be careful of injury from a broken display module. 21. please avoid the pressure adding to the surface (front or rear side) of modules, because it will cau se the display non-uniformity or other function issue. www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of A080SN01-V4

	To Download A080SN01-V4 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .